debian squeeze install software raid 1
The most important tool for setting up RAID is mdadm. Let's install it...
The most important tool for setting up RAID is mdadm. Let's install it like this: apt-get install initramfs-tools mdadm. MD arrays How To Set Up Software RAID1 On A Running LVM System.
⬇ Download Full VersionActually, you can have root on RAID1+LVM partition. This page Root on softw...
Actually, you can have root on RAID1+LVM partition. This page Root on software RAID+LVM. In this example, we In Jessie (), and I believe Wheezy (), the installer will install GRUB even on RAID installs. However.
⬇ Download Full VersionRecently I needed to setup software RAID1 during Debian installation proces...
Recently I needed to setup software RAID1 during Debian installation process. Create empty partition table on each disk used to create RAID1 array. Continue installation process up to the install the grub boot loader on a hard disk menu.
⬇ Download Full VersionYou should install grub on your disks MBR, not on /dev/md0, so run grub-ins...
You should install grub on your disks MBR, not on /dev/md0, so run grub-install /dev/sda ; grub-install /dev/sdb. Is this work better?
⬇ Download Full VersionThis post documents the steps I followed to retrofit RAID1 into an existing...
This post documents the steps I followed to retrofit RAID1 into an existing Debian squeeze installation. Getting a mirrored setup after the fact.
⬇ Download Full Versioninstallation of debian wheezy on mdadm raid1 + gpt swapping the raid contro...
installation of debian wheezy on mdadm raid1 + gpt swapping the raid controller in case it dies is an option. mdadm [software] raid1 might be.
⬇ Download Full VersionThis document gives an example on how to setup a clean Linux system which c...
This document gives an example on how to setup a clean Linux system which can boot directly from a software RAID device. The procedure.
⬇ Download Full VersionTo create a software RAID1 on a running system, we have to prepare the Chan...
To create a software RAID1 on a running system, we have to prepare the Change the partitions type on /dev/sdb to Linux raid autodetect.
⬇ Download Full VersionSoftware RAID1, Debian squeeze fresh installation, GRUB2 I am going to use ...
Software RAID1, Debian squeeze fresh installation, GRUB2 I am going to use software RAID1 to mirror the hard drive and also use rdiff-backup to make a.
⬇ Download Full VersionIf the two disks are /dev/sda and /dev/sdb, run both grub-install /dev/sda ...
If the two disks are /dev/sda and /dev/sdb, run both grub-install /dev/sda and grub-install /dev/sdb. Then both drives will be able to boot alone.
⬇ Download Full VersionLooks like somehow Debian installer screws up the partition table. The &quo...
Looks like somehow Debian installer screws up the partition table. The "bios_grub" flag gets removed and becomes "raid" flag. The fix is to.
⬇ Download Full Version2 raid1 device - /dev/md0 (made of /dev/sda1 and /dev/sdb1) for Finally I w...
2 raid1 device - /dev/md0 (made of /dev/sda1 and /dev/sdb1) for Finally I wanted to install grub on the new disk (being /dev/sdb now) and it.
⬇ Download Full VersionHowto | Install Debian Squeeze With Raid1 + LVM so I added a second gb SATA...
Howto | Install Debian Squeeze With Raid1 + LVM so I added a second gb SATA; so that I could have a simple software RAID array.
⬇ Download Full VersionRaider is a tool to automate linux software raid conversion. It is able to ...
Raider is a tool to automate linux software raid conversion. It is able to convert a single linux system disk in to a software raid 1, 4, 5, 6 or 10 system in a two-pass simple command. dwn.220.v.ua; To uninstal simply run the uninstall script as root: #. -raid1-on-a-running-lvm-system-incl-grub2-configuration-debian-squeeze.
⬇ Download Full VersionBooting and Starting the Installer. Once the BIOS has begun booting from .....
Booting and Starting the Installer. Once the BIOS has begun booting from .. You must then choose “Configure software RAID” in the partitioning tool to.
⬇ Download Full Version