grub boot on software raid

If the two disks are /dev/sda and /dev/sdb, run both grub-install /dev/sda ...

If the two disks are /dev/sda and /dev/sdb, run both grub-install /dev/sda and grub-install /dev/sdb. Then both drives will be able to boot alone.

⬇ Download Full Version

I created a small bootable GRUB partition (I chose the partition editor...

I created a small bootable GRUB partition (I chose the partition editor's How To Install Ubuntu With Software RAID1 | HowtoForge - Linux.

⬇ Download Full Version

This tutorial will use SYSLINUX instead of GRUB. GRUB when used in conjunct...

This tutorial will use SYSLINUX instead of GRUB. GRUB when used in conjunction with GPT requires an additional BIOS Boot  ‎Introduction · ‎Installation · ‎Prepare the hard drives · ‎RAID installation.

⬇ Download Full Version

Configuring the RAID; Boot Loader; Boot from Degraded Disk; Verify the RAID...

Configuring the RAID; Boot Loader; Boot from Degraded Disk; Verify the RAID This is a form of software RAID using special drivers, and it is not In case your next HDD won't boot then simply install Grub to another drive.

⬇ Download Full Version

This article describes how to setup a Linux system that can boot directly f...

This article describes how to setup a Linux system that can boot directly from a software RAID-1 device using GRUB. Even if one of the disks in.

⬇ Download Full Version

I am have a problem installing the boot loader on to the software RAID devi...

I am have a problem installing the boot loader on to the software RAID device /dev/md0. When I have done so the machine won't boot.

⬇ Download Full Version

The GRUB bootloader will be configured in such a way that the system will s...

The GRUB bootloader will be configured in such a way that the system will still be able to boot if one of The most important tool for setting up RAID is mdadm.

⬇ Download Full Version

The problem is, the grub bootloader doesn't know about the software RA...

The problem is, the grub bootloader doesn't know about the software RAID, so it only installs the bootloader on the first drive. Which is good.

⬇ Download Full Version

You tagged software-raid, so learning grub can help: How to boot after RAID...

You tagged software-raid, so learning grub can help: How to boot after RAID The GRUB Legacy (boot manager) file doesn't identify disks the.

⬇ Download Full Version

Root on software RAID+LVM Install the bootloader (GRUB). In Jessie () After...

Root on software RAID+LVM Install the bootloader (GRUB). In Jessie () After first boot, consider executing dpkg-reconfigure grub-pc (or.

⬇ Download Full Version

Hello All, I am trying to setup a RAID 1 on my system that has 2 identical ...

Hello All, I am trying to setup a RAID 1 on my system that has 2 identical IDE hard disks. I am installing CentOS x64 and doing a software.

⬇ Download Full Version

I select manual set and create the paritions and software raid and assign E...

I select manual set and create the paritions and software raid and assign EXT 4 and Swap. But when it gets to "Install the GRUB boot loader".

⬇ Download Full Version

Hi, I was reloading my linux box from scratch recently and decided to try s...

Hi, I was reloading my linux box from scratch recently and decided to try software RAID 0 since I have two identical 75GB drives and figured this.

⬇ Download Full Version

Hi, I was reloading my linux box from scratch last night and decided to try...

Hi, I was reloading my linux box from scratch last night and decided to try software RAID 0 since I have two identical 75GB drives and figured.

⬇ Download Full Version

Ubuntu requires manual partitioning for the software RAID array. RAID on GP...

Ubuntu requires manual partitioning for the software RAID array. RAID on GPT disks (larger than 2+TB), you must create a GRUB bootloader partition on each.

⬇ Download Full Version