debian squeeze install software raid

I needed to setup software RAID1 during Debian installation process. During...

I needed to setup software RAID1 during Debian installation process. During partition creation process select physical volume for RAID as.

⬇ Download Full Version

Hello members, how can I install a Linux Software-RAID 1 on Debian Squeeze ...

Hello members, how can I install a Linux Software-RAID 1 on Debian Squeeze using mdadm (2 disks: sda sdb)? On google and a lot of linux.

⬇ Download Full Version

This document gives an example on how to setup a clean Linux system which c...

This document gives an example on how to setup a clean Linux system which can boot directly from a software RAID device. The procedure.

⬇ Download Full Version

The Debian installer will set everything up for you if you choose that to r...

The Debian installer will set everything up for you if you choose that to retrofit RAID1 into an existing Debian squeeze installation. . Why do you use rsync, and don't directly setup the active mirror letting the RAID driver let.

⬇ Download Full Version

I don't think LVM in Squeeze supported RAID5. In the Debian Installer,...

I don't think LVM in Squeeze supported RAID5. In the Debian Installer, partition each disk to have a ~MB partition and a second partition.

⬇ Download Full Version

For some reason, your initramfs is failing to start your RAID array. When p...

For some reason, your initramfs is failing to start your RAID array. When prompted about where to install grub, you most likely want to pick.

⬇ Download Full Version

I am following these instructions: dwn.220.v.ua...

I am following these instructions: dwn.220.v.ua

⬇ Download Full Version

You should install grub on your disks MBR, not on /dev/md0, so run grub-ins...

You should install grub on your disks MBR, not on /dev/md0, so run grub-install /dev/sda ; grub-install /dev/sdb. Is this work better?

⬇ Download Full Version

Ok, so I found solution of my problem booting from mdadm Raid1. I'm qu...

Ok, so I found solution of my problem booting from mdadm Raid1. I'm quite ashamed that it took me so much time to figure this out, because it's.

⬇ Download Full Version

This configuration is often called “dual boot”, and the Debian installation...

This configuration is often called “dual boot”, and the Debian installation system can .. Furthermore, this mode is unavoidable if you wish to use software RAID.

⬇ Download Full Version

to install grub on the second disk, so you could boot from it to. setup a c...

to install grub on the second disk, so you could boot from it to. setup a clean Linux system which can boot directly from a software RAID device. and my question specifically was i couldn't find grub in debian squeeze.. after.

⬇ Download Full Version

installation of debian wheezy on mdadm raid1 + gpt Using Configure software...

installation of debian wheezy on mdadm raid1 + gpt Using Configure software RAID i'm creating raid 1 devices on pairs of partitions earlier.

⬇ Download Full Version

It came with a gb SATA, so I added a second gb SATA; so that I could have a...

It came with a gb SATA, so I added a second gb SATA; so that I could have a simple software RAID array. I also added 2gb of Crucial.

⬇ Download Full Version

28 Apr 16 Installing GRUB2 on mdadm software Raid in Debian Wheezy/Jessie. ...

28 Apr 16 Installing GRUB2 on mdadm software Raid in Debian Wheezy/Jessie. Principle: If you look at the result of the command df -h and you are using the.

⬇ Download Full Version

Setting up simple software RAID-1 on Debian 5. allanrbo Especially thanks f...

Setting up simple software RAID-1 on Debian 5. allanrbo Especially thanks for including the GRUB setup.

⬇ Download Full Version