ngdbuild logical net has multiple drivers

Hi, I am using PlanAhead with two reconfigurable modules. Each having two d...

Hi, I am using PlanAhead with two reconfigurable modules. Each having two different partitions. When i try tp launh the run on one of dwn.220.v.ua: NgdBuild - Multiple drivers - Community.

⬇ Download Full Version

If signals or ports are left unconnected in my design, NGDBuild issues the ...

If signals or ports are left unconnected in my design, NGDBuild issues the following errors: "ERROR:NgdBuild - logical net "N17" has multiple drivers.

⬇ Download Full Version

I receive the following error when running Translate although there appears...

I receive the following error when running Translate although there appears to be only one driver on a given net (e.g: 'signal_name'). "ERROR:NgdBuild

⬇ Download Full Version

A new port 'net_gnd0' has been added and is connected to this. si...

A new port 'net_gnd0' has been added and is connected to this. signal. ERROR:NgdBuild - logical net 'net_gnd0' has multiple driver(s). pin G on block.

⬇ Download Full Version

ERROR - ngdbuild: logical net 'data[6]' has multiple drivers. ERR...

ERROR - ngdbuild: logical net 'data[6]' has multiple drivers. ERROR - ngdbuild: DRC failed with 7 errors and 0 warnings. Done: error code 2error in synthesis ISE - Forum for Electronics.

⬇ Download Full Version

ERROR:NgdBuild - logical net 'myclknot' has multiple driver(s): p...

ERROR:NgdBuild - logical net 'myclknot' has multiple driver(s): pin O on block myclknot1_INV_0 with type INV, pin PAD on block myclknot.

⬇ Download Full Version

i'm getting: ERROR:NgdBuild - logical net 'CLKX' has multipl...

i'm getting: ERROR:NgdBuild - logical net 'CLKX' has multiple driver(s): pin CLK2X on block clockdoubler/DCM_INST with type DCM.

⬇ Download Full Version

xilinx:ngdbuild ngdbuild -intstyle ise -dd _ngo -nt timestamp -uc [UCF cons...

xilinx:ngdbuild ngdbuild -intstyle ise -dd _ngo -nt timestamp -uc [UCF constraint file] -p [device ERROR: logic net has multiple driver(s).

⬇ Download Full Version

ERROR:NgdBuild - logical net has multiple driver(s). ERROR:NgdBuild - input...

ERROR:NgdBuild - logical net has multiple driver(s). ERROR:NgdBuild - input pad net drives multiple.

⬇ Download Full Version

メッセージ. ERROR - ngdbuild: logical net '信号名' has multiple drivers W...

メッセージ. ERROR - ngdbuild: logical net '信号名' has multiple drivers WARNING - ngdbuild: logical net 'インスタンス名/信号名' has no load. 意味. 指定された.

⬇ Download Full Version

ERROR:NgdBuild - logical net 'rst_in' has multiple drivers. The p...

ERROR:NgdBuild - logical net 'rst_in' has multiple drivers. The possible drivers causing this are: pin G on block XST_GND with type GND.

⬇ Download Full Version

ERROR:NgdBuild - logical block 'okHI/hicore' with type ERROR:NgdB...

ERROR:NgdBuild - logical block 'okHI/hicore' with type ERROR:NgdBuild - logical net 'ok1' has multiple driver(s): pin PAD on block.

⬇ Download Full Version

pin O on block wb_dat_iLogicTrst4 with type LUT4 ERROR:NgdBuild - logical n...

pin O on block wb_dat_iLogicTrst4 with type LUT4 ERROR:NgdBuild - logical net 'wb_dat_i' has multiple driver(s).

⬇ Download Full Version

ERROR:NgdBuild - logical net 'fpga_0_radio_bridge_slot_2_radio_DIPSW_p...

ERROR:NgdBuild - logical net 'fpga_0_radio_bridge_slot_2_radio_DIPSW_pin_0_IBUF' has multiple driver(s): pin G on block.

⬇ Download Full Version

If multiple IBUF (and OBUF) type components are connected in series, NGDBui...

If multiple IBUF (and OBUF) type components are connected in series, NGDBuild reports the errors as listed above. Examples of IBUF-type.

⬇ Download Full Version